Ritetite Control is a single-component gel super glue engineered for ultra-fast bonding and high-accuracy application. With a translucent finish and a specially designed thixotropic (non-run) formula, it grabs fast and stays where you place it—ideal when you need clean, controlled adhesive placement without the spreading and leaking you get from traditional thin superglues.
It polymerises (hardens) rapidly by reacting with surface moisture, allowing most materials to bond in around 30 seconds (surface and conditions dependent). The thicker gel consistency makes Ritetite Control a standout for poor-fitting repairs and uneven surfaces, including rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber applications.
Supplied in a large 100ml container with an integrated nozzle for easy, precise application.
Key features & benefits
-
Translucent finish for a cleaner look on repairs
-
Bonds most materials in ~30 seconds (application dependent)
-
High-viscosity gel for greater accuracy and detail
-
Non-run formula helps prevent spreading and drips
-
100ml size for higher usage and better value
-
Integrated nozzle for controlled dispensing
Typical applications
-
Rough or uneven metal and ceramic repairs
-
Metal-to-metal bonding where surfaces aren’t perfectly finished
-
Metal-to-rubber bonding and patch repairs
-
General high-speed assembly where control and fast cure are essential
Surface preparation (for best bond)
Surfaces should be clean, dry and grease-free before applying adhesive. Degrease using a suitable solvent such as acetone or isopropanol.
Some metals (e.g. aluminium, copper and alloys) benefit from light abrasion (emery cloth or similar) to remove oxide before bonding.
Directions for use
-
Apply adhesive sparingly to one surface.
-
Bring components together quickly, correctly aligned.
-
Apply firm pressure so adhesive spreads into a thin film.
-
Do not disturb or re-align until initial strength is achieved (often seconds).
-
Remove surplus adhesive using an appropriate solvent such as nitromethane or acetone.
Note: For difficult or porous surfaces, use a super glue accelerator/activator. For bonding PP, PE, PTFE or silicone, use a suitable primer first.
No delivery surcharge on orders over $98. If the amount is not reached, a single $18 fee will be applied to your total.
For more information please access our Shipping and Returns T&C page.
Ritetite Control is a single-component gel super glue engineered for ultra-fast bonding and high-accuracy application. With a translucent finish and a specially designed thixotropic (non-run) formula, it grabs fast and stays where you place it—ideal when you need clean, controlled adhesive placement without the spreading and leaking you get from traditional thin superglues.
It polymerises (hardens) rapidly by reacting with surface moisture, allowing most materials to bond in around 30 seconds (surface and conditions dependent). The thicker gel consistency makes Ritetite Control a standout for poor-fitting repairs and uneven surfaces, including rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber applications.
Supplied in a large 100ml container with an integrated nozzle for easy, precise application.
Key features & benefits
-
Translucent finish for a cleaner look on repairs
-
Bonds most materials in ~30 seconds (application dependent)
-
High-viscosity gel for greater accuracy and detail
-
Non-run formula helps prevent spreading and drips
-
100ml size for higher usage and better value
-
Integrated nozzle for controlled dispensing
Typical applications
-
Rough or uneven metal and ceramic repairs
-
Metal-to-metal bonding where surfaces aren’t perfectly finished
-
Metal-to-rubber bonding and patch repairs
-
General high-speed assembly where control and fast cure are essential
Surface preparation (for best bond)
Surfaces should be clean, dry and grease-free before applying adhesive. Degrease using a suitable solvent such as acetone or isopropanol.
Some metals (e.g. aluminium, copper and alloys) benefit from light abrasion (emery cloth or similar) to remove oxide before bonding.
Directions for use
-
Apply adhesive sparingly to one surface.
-
Bring components together quickly, correctly aligned.
-
Apply firm pressure so adhesive spreads into a thin film.
-
Do not disturb or re-align until initial strength is achieved (often seconds).
-
Remove surplus adhesive using an appropriate solvent such as nitromethane or acetone.
Note: For difficult or porous surfaces, use a super glue accelerator/activator. For bonding PP, PE, PTFE or silicone, use a suitable primer first.
No delivery surcharge on orders over $98. If the amount is not reached, a single $18 fee will be applied to your total.
For more information please access our Shipping and Returns T&C page.